Marine construction
Pile gates
Pile gates and piling gates designed and built for 300 mm guide piles to 12 m monopiles.
A pile gate holds a pile in position and on line while it is pitched, gripped and driven or drilled in. We design each gate to the pile, the structure it works from and the installation method.
Pile sizes
| Pile type | Typical diameter | Where it’s used | What the gate does |
|---|---|---|---|
| Monopiles | up to 12 m | Offshore wind foundations | Holds and centres the pile for verticality while it’s driven. Usually called a pile gripper or gripper frame |
| Jacket and pin piles | around 2 m | Offshore wind jacket foundations, offshore platforms | Guides pre- or post-installed piles to the jacket or template interface |
| Tubular and king piles | mid-range diameters | Jetties, quays, berthing and mooring dolphins | Restrains the pile at one or more levels, often raked, from a jack-up, barge or the previous bent |
| Sheet and combi-walls | king piles with intermediate sheets | Quay walls, deep-water berths, cofferdams | Sets king-pile position, rotation and clutch orientation so the wall closes on line |
| Small-diameter piles | from 300 mm | Pontoon guide piles, moorings, temporary works | Simple, quick-to-set restraint for high piling rates |
Pile gate types
- Single-level restraint. Guidance for short piles and simple installations.
- Twin-level and multilevel gates. Hold the pile at two or more heights for verticality or rake control, with access to each level.
- Articulated and trunnion-mounted gates. Swing clear of the installed pile so the next one can be pitched, without re-rigging the gate.
- Gripper arrangements. Hydraulic or mechanical grippers that centre the pile and hold it as it advances.
- Jack-up, barge and pontoon-mounted gates. Cantilever and shelf supports that interface mechanically and structurally with the vessel or platform. One gate design can suit several jack-ups.
- Walking pile gates. Supported at one end on a spud leg and at the other on a previously installed pile, so the gate moves forward with the work, with no fixed platform to relocate.
- Cantitravel pile gates. Gates and support systems for cantilever-travelling (cantitravel) piling, working from the structure itself as it is built out over the water.
- Rollover and upending frames. Turn a pile from horizontal to vertical ready for pitching. Supplied alongside the gate.
- Vertical or raked. Configured to the foundation geometry.
Pile gate design features
- Tolerance. Position, verticality or rake and rotation are set by the gate.
- Fewer crane lifts. Gates that adjust mechanically, or install several piles per set-up, free the main crane for pitching.
- Less work at height. Integral access and remotely operated grippers keep crews clear of the pile.
- Higher piling rates. Faster repositioning between piles and hammer clearance through the gate.
Pile gate experience
We have designed pile gates for nuclear new-build marine works, port and quay expansions, deep-water berths, jetties, berthing dolphins and offshore wind. That covers twin-level, articulated and trunnion-mounted gates, gates working from jack-ups and barges and walking gates that carry a jetty forward pile by pile.
For a published example, see our Portland pile gates case study: twin-level gates for a 400 m combi-wall at a new deep-water berth.
Design, certification and assurance
Gates are designed to the loads of the installation method: pile self-weight, hammer or drilling reactions, environmental loads on the pile and the gate, and the vessel or structure interface. Certification to DNV, Lloyd’s Register, Bureau Veritas and ABS is available where the project requires it, with documentation for project assurance and independent checking.
Pile gate FAQs
What is a pile gate?
A temporary steel structure that holds a pile in position and on line during installation. It restrains the pile at one or more levels while it is pitched and driven, vibrated or drilled. It is also called a piling gate, pile guide frame or, for monopiles, a pile gripper.
What’s the difference between a pile gate, a pile gripper and a piling template?
A pile gate restrains piles from a jack-up, barge or structure above the water. A pile gripper is a gate with active grippers, usually for large monopiles. A piling template sits on the seabed and sets the position of several piles at once. We design all three. See subsea piling templates.
What pile sizes can you handle?
From 300 mm guide piles to 12 m monopiles, including jacket pin piles, tubular and king piles and combi-walls.
Can a gate fit our jack-up or barge?
Yes. Gates are designed with cantilever or shelf supports to suit the vessel, and one gate design can be made to interface with several jack-ups.
What is a walking pile gate?
A gate that is carried forward by the work it is installing. One end sits on a spud leg and the other on the last pile installed. Once a bent is complete, the gate steps forward onto the new pile, so a jetty or quay can be built continuously without relocating a fixed platform.
Can you supply pile gates for cantitravel piling?
Yes. We design and build pile gates and the supporting skidding systems for cantilever-travelling (cantitravel) piling, where the rig works from the structure it is building and moves forward bay by bay.
Do you only design, or build as well?
Both. We can deliver a design package for your fabricator, or the complete gate, controls and commissioning, turnkey.